Tag Archives: weaving

LOYALHANNON SPINNERS

LOYALHANNON SPINNERS

n Spinners

Loyalhannon Spinners has been helping interested folks learn to spin and explore the world of fiber arts. They are active in the fiber arts community and conduct educational demonstrations in the Westmoreland County Fair, the Fiber to Shawl Contest in Washington Count and the PA Farm Shows in Harrisburg. They meet the third Saturday of the month from 1:00 – 4:00 p.m. at the Grist Mill on the campus of St. Vincent College, Latrobe, PA.

Follow them on Facebook.

 

 

Share Button

WEAVING PROJECT: WEAVING WITH A SIMPLE FRAME

WEAVING PROJECT: WEAVING WITH A SIMPLE FRAME

The craft WEAVING WITH A SIMPLE FRAME is an updated adaption of the project “A Simple Weaving Frame” found in The Reinhold Book of Arts and Crafts Techniques published by Van Nostrand Reinhold Co., a division of Litton Education Publishing Inc. in 1976. Many important events happened in 1976.

Challenge yourself and always use your imagination!

Materials:

Cardboard

String

Ruler

Pencil/eraser

Scissors

Yarn

Large-eyed tapestry needle (optional)

Ribbon, feathers,  wool and other strips of fabric, leaves, twigs, string

At all times refer to the photo illustrations.

  1. Weaving consists of a warp and a weft. The warp comprises the vertical strings of the loom while the weft consists of the yarn interlaced through the weft. Take a piece of strong cardboard. Measure and cut ¼” incisions at regular intervals of ¼” to 1/8” on both ends of the cardboard.
  2. To make the warp: Take heavy string (i.e., kite string) and make a knot at one end. Loop the string from one end of the cardboard to the other and back up again. When finished, cut and make a knot in the back or tape the end of the string to the back of the cardboard. (Always leave a little extra string at either end.)
  3. To make the weft: Think of a theme or a design for the weaving. The design is up to you! Use a variety of materials to weave in and out as you did with the paper weaving. (The weaving below was woven with pipe cleaners and kite string but almost anything goes!)
  4. Start with about an inch and a half of warp at the bottom. Make sure strips of material alternate with each row. Roll the material into a ball if possible and pass it through the warp back and forth for several rows depending on the design. Tuck the end in the back of the warp. Do not tie a knot.
  5. Tips: Consider using a the tapestry needle to weave the yarn and string. A ruler will help you lift the warp so you can pass material through easily but you must lift every other string (see step 4.)
  6. When the weaving is finished, cut any loose thread in the back of the warp but don’t cut too close to the weft.
Share Button

WEAVING PROJECTS: PAPER WEAVING

WEAVING PROJECTS: PAPER WEAVING

PAPER WEAVING

PAPER WEAVING

PAPER WEAVING

PAPER WEAVING

PAPER WEAVING

PAPER WEAVING

PAPER WEAVING

PAPER WEAVING

PAPER WEAVING

PAPER WEAVING

The craft PAPER WEAVING was adapted from the  project “Stitches, Scraps and Haute Couture/Paper Weaving” found  in Arts and Crafts Activities Desk Book by Joyce Novis Laskin and published by Parker Publishing Company in 1971.

MATERIALS:

Large sheet of thick paper or cardboard for the frame of the mock loom

Two or three different colored and/or pattered papers cut into strips

Ribbon (optional)

Scissors

Ruler

Pencil with eraser

Glue stick or scotch tape

  1. Fold paper in half. (Choose any size paper or cardboard from 8 ½” x 11” and up.) Draw lines ¼” to ¾” apart down the length of the fold.
  2. Look at Step II below. Make incisions with the scissors, starting from the fold up to ½” of the edges of the paper. Don’t cut all the way to the end or you will cut the paper/cardboard into strips! Cut up to ½”  at each the end of the paper/cardboard and draw a line across. (In other words, leave an uncut margin at both ends.) This is the weaving “frame” or “loom.” Open the paper or cardboard.
  3. Measure and cut strips of paper to weave in and out of the paper loom. To minimize mistakes, make sure that the strips are a little longer than the width of the loom.
  4. Choose two or three different colored papers to weave through the paper loom. (Alternate ribbon with paper for a different look to the weaving.)  Start at one end and work your way up to the other end. Alternate the in-and-out pattern with each row. (Refer to photograph.)
  5. Trim loose ends and glue the ends down using a glue stick.
  6. Use your paper weaving as a placemats or give it as a gift.  What else can you do with your paper weaving?
Share Button

Lazy Day Crafts: Weaving With a Simple Frame

Lazy Day Crafts: Weaving With a Simple Frame

 

Materials:

Cardboard

String

Ruler

Pencil/eraser

Scissors

Yarn

Large-eyed tapestry needle (optional)

Ribbon

Feathers

Wool

Strips of fabric

Leaves

Twigs

String

  1. Weaving consists of a warp and a weft. The warp comprises the vertical strings of the loom while the weft consists of the yarn horizontally interlaced through the weft. Take a piece of strong cardboard. Measure and cut ¼” incisions at regular intervals of ¼” to 1/8” on both ends of the cardboard.
  2. To make the warp: Take heavy string (i.e., kite string) and make a knot at one end. Stretch a continuous length of string across the cardboard. In other words, loop the string from one end of the cardboard to the other and back up again. When finished, cut and make a knot in the back or tape it to the back of the cardboard. Always leave a little extra string for knotting at either end.
  3. To make the weft: Think of a theme or a design for the weaving. The design is up to you! Use a variety of materials to weave in and out as you did with the paper weaving. Start with about an inch and a half of warp at the bottom. Make sure strips of material alternate with each row.  Roll the material into a ball if possible and pass it through the warp back and forth for several rows depending on the design. Tuck the end in the back of the warp. Do not tie a knot.
  4. Tips: You can using the tapestry needle to weave. A ruler will help you if the warp so you can pass material through easily but you must lift every other string.
  5.  When weaving is finished, cut any loose thread in the back of the warp but don’t cut too close to the weft.
Share Button

Part I: Sights and Sounds from the Pittsburgh Folk Festival 2015

Part I: Sights and Sounds from the Pittsburgh Folk Festival 2015
Share Button

Our Imaginations! Camp for Kids: Weaving with a Simple Frame

Our Imaginations! Camp for Kids: Weaving with a Simple Frame

The craft WEAVING WITH A SIMPLE FRAME is an updated adaption of the project “A Simple Weaving Frame” found in The Reinhold Book of Arts and Crafts Techniques published by Van Nostrand Reinhold Co., a division of Litton Education Publishing Inc. in 1976. Many important events happened in 1976.

Challenge yourself and always use your imagination!

Materials: Cardboard

String

Ruler

Pencil/eraser

Scissors

Yarn

Large-eyed tapestry needle (optional)

Ribbon, feathers,  wool and other strips of fabric, leaves, twigs, string

* At all times refer to the photo illustrations.

  1. Weaving consists of a warp and a weft. The warp comprises the vertical strings of the loom while the weft consists of the yarn interlaced through the weft. Take a piece of strong cardboard. Measure and cut ¼” incisions at regular intervals of ¼” to 1/8” on both ends of the cardboard.
  2. To make the warp: Take heavy string (i.e., kite string) and make a knot at one end. Loop the string from one end of the cardboard to the other and back up again. When finished, cut and make a knot in the back or tape the end of the string to the back of the cardboard. (Always leave a little extra string at either end.)
  3. To make the weft: Think of a theme or a design for the weaving. The design is up to you! Use a variety of materials to weave in and out as you did with the paper weaving. (The weaving below was woven with pipe cleaners and kite string but almost anything goes!)
  4. Start with about an inch and a half of warp at the bottom. Make sure strips of material alternate with each row. Roll the material into a ball if possible and pass it through the warp back and forth for several rows depending on the design. Tuck the end in the back of the warp. Do not tie a knot.
  5. Tips: Consider using a the tapestry needle to weave the yarn and string. A ruler will help you lift the warp so you can pass material through easily but you must lift every other string (see step 4.)
  6. When the weaving is finished, cut any loose thread in the back of the warp but don’t cut too close to the weft.
Frame for weaving

Frame for weaving

Preparing the frame

Preparing the frame

 

Beginning to weave

Beginning to weave

 

The finished weaving

The finished weaving

v

Share Button